White Screen Issue
#1
Got everything built and put together. I installed the newest image and I cannot get the LCD screen to show anything but a white screen. I've plugged it into my TV and it comes up fine. Is there any way to kick start the screen itself? I've only gotten it to work once since I've been messing with it.
Reply
#2
If you are using the SD card image that we provide, then I would have to assume that the problem is either where the LCD connects to our circuit board or where the Pi connects to our circuitboard.

Can you post any photos of those two areas? In particular we might want to look at the soldering on the back of the Pi.
Card Fighters' Clash 2 English Translation ( http://cfc2english.blogspot.com/ )
Neo Geo Pocket Flash Cart and Linker Project ( http://www.flashmasta.com/ )
Avatar art thanks to Trev-Mun ( http://trevmun.deviantart.com/ )
Reply
#3
It's fixed.  I believe the ribbon wasn't quite seated right.  After I took it apart to take pictures the ribbon was slightly out.  Put it back as far in as I could and it started working correctly. I didn't see any of the connectors when I put it in so I didn't give it a second thought when debugging.
Reply
#4
Oh, great news, tenorxander95! Thanks for the update!
Card Fighters' Clash 2 English Translation ( http://cfc2english.blogspot.com/ )
Neo Geo Pocket Flash Cart and Linker Project ( http://www.flashmasta.com/ )
Avatar art thanks to Trev-Mun ( http://trevmun.deviantart.com/ )
Reply
#5
Hi,

I've got a white screen issue also, ribbon looks good. Is there an image I can try thats already configured to work with the screen?
Reply
#6
Try at http://Freeplaytech.com/build/
Card Fighters' Clash 2 English Translation ( http://cfc2english.blogspot.com/ )
Neo Geo Pocket Flash Cart and Linker Project ( http://www.flashmasta.com/ )
Avatar art thanks to Trev-Mun ( http://trevmun.deviantart.com/ )
Reply
#7
Thanks. Makes sense...

Link is even on the instruction page, totally missed it.... so dumb :| Trying it right now! Smile
Reply
#8
(12-24-2017, 07:36 PM)kevinhorsten Wrote: Thanks. Makes sense...

Link is even on the instruction page, totally missed it.... so dumb :| Trying it right now! Smile

I wouldn't say dumb.  We need to figure out a way to make this more obvious.  It's probably the #1 support question.  On the upside, it's also the easiest support question to answer, so it makes us feel good.  Smile
Card Fighters' Clash 2 English Translation ( http://cfc2english.blogspot.com/ )
Neo Geo Pocket Flash Cart and Linker Project ( http://www.flashmasta.com/ )
Avatar art thanks to Trev-Mun ( http://trevmun.deviantart.com/ )
Reply
#9
I have tried all the tips I have read on here for the white screen and can't figure out what I am doing wrong. I am using the solderless GPIO header and the ribbon cable is plugged in as far as will go in. I can get a green led light on the main board and the screen lights up and stays white. If I plug my hdmi in at that time it displays on my monitor. Only thing I can think is wrong is the header but it looks good and plugs in tight.
Reply
#10
Could you post some pictures of your hammered Pi header? It is possible to hammer in too far, and then it won’t make a perfect connection.
Card Fighters' Clash 2 English Translation ( http://cfc2english.blogspot.com/ )
Neo Geo Pocket Flash Cart and Linker Project ( http://www.flashmasta.com/ )
Avatar art thanks to Trev-Mun ( http://trevmun.deviantart.com/ )
Reply


Forum Jump:


Users browsing this thread: 1 Guest(s)